HKEY_CURRENT_USER\Software\Microsoft\Office\16.0\Outlook\AutoDiscover

Create a DWORD named ExcludeExplicitO365Endpoint

Set value to 1

Restart Outlook

DisablePersonalDirChange = (0)

Here's How:
Open up your RDP connection, click on the Advanced Tab, then click on the Connect from anywhere Settings Button.
Next, click on the Use these RD Gateway server settings and enter the IP address of your SBS server or fully qualified domain to connect to it. Example: remote.yourdomain.com
Click OK, then in the General Tab, enter the computer name of the computer you are trying to access that is inside your office. Example: mycomputer-pc
Next, enter your domain user name and password, save the connection settings and login!

This is much easier than using Internet Explorer in compatibility view settings, replacing dll's as Microsoft patches them with incompatible versions, etc.

On the computer used to connect to the remote computer:

I got it working as a workaround by replacing the mstscax.dll (Version 10.0.14393.0) in %windir%\SysWOW64\ with the "backup file" in "Windows.old\WINDOWS\SysWOW64" version (10.0.10586.494)

I had to take ownership of the file and give Administrators Full control access to be able to replace the file.

dos2unix filenameToModify

find . -name '*.php' | while read FILE; do if grep '$GLOBALS' "$FILE"; then echo "$FILE" >> maybeinfected; fi ; done

find . -name '*.php' | while read FILE; do if grep 'eval(base64_decode' "$FILE"; then echo "$FILE" >> maybeinfected; fi ; done

find . -name '*.php' | while read FILE; do if grep '''PCT4BA6ODSE_"$FILE"; then echo "$FILE" >> maybeinfected; fi ; done

Automatically delete any that match a pattern:

find . -name '*.php' | while read FILE; do if grep 'PCT4BA6ODSE_' "$FILE"; then rm  "$FILE" -rf; fi ; done

sub window_onload()
Dim targetMachineName
Dim version 
On Error Resume Next
version = MsRdpClient.Version
if Err then
  msgbox ControlLoadFailed_ErrorMessage,0,RemoteDesktopCaption_ErrorMessage
  exit sub
end if  
On Error GoTo 0
if strcomp(version,"6.0.6000") < 0 then
   msgbox IncorrectClientVersion_ErrorMessage, 0, RemoteDesktopCaption_ErrorMessage
   window.close
   exit sub
end if

What I did was to comment out the second part of that statement so it looks like this

'if strcomp(version,"6.0.6000") < 0 then
'   msgbox IncorrectClientVersion_ErrorMessage, 0, RemoteDesktopCaption_ErrorMessage
'   window.close
'   exit sub
'end if

Check the /etc/resolv.conf
Make sure they are all valid and responding...especially the first one!

HKLM\Software\Microsoft\MSLicensing

At this point, they try and scare you into thinking there really could be some problems by showing you the red X critical error messages that EVERY event viewer will have!  Next, they will ask for money or try and direct you to a screen sharing tool so that they can access your computer.  DON"T DO IT!  My suggestion is to play along until they give you a key that provides them with access to your computer.  Write the number down and hang up.  You can report this fraudulant activity to the company that hosts the website that they were trying to use to access your computer.  They key will allow that compnay to disable their account and report the fraudulant activity to the proper authorities.

Network is a major factor in computing. Windows 7 computers will be slow in accessing shares on old MS Windows servers and non MS Operating systems including Sun and Linux. Accessing data and transferring data over network are still problem in this case. Resolving DNS requests internally (LAN or WAN) and externally (Internet) also could be slow in Windows 7. The following methods I’m listing out is worked for me to speed up Windows 7 networking with NT,2003 and Sun servers.

How to Fix Windows 7 network slow problem?

1) Disable Autotuning

Disabling autotuning will help much on DNS lookup and network discovery. It improves the data transfer speed also over the network. Disabling autotuning in windows 7 is very similar to Windows vista method. Read more here about disabling autotuning in windows vista.

To recap important steps,

Start command prompt as administrator, and follow the commands as shown in below example.

netsh interface tcp show global

netsh interface tcp set global autotuning=disabled

netsh interface tcp show global

Windows 7 Network slow

2) Remove RDC ( Remote Differential Compression)

This feature introduced with Windows Vista to transfer data over network in compressed format. The same RDC feature continued in Windows 7 also. Since most of the old operating systems came before vista do not support this RDC feature, it slows down network data transfer in windows 7. You can remove this RDC (Remote Differential Compression) in windows 7 by visiting control panel and programs and features. Click on ‘Turn Windows features on or off’, as shown below.
Remove RDC ( Remote Differential Compression) in Vista

Windows 7 Network slow

3) Remove IPv6 from network properties.

If your internal or external networks do not  require  IPv6 protocol, better remove it under network connection properties. Keeping IPv6 in your computer sometimes slows down network by trying to register IPv6 addresses, or trying to get IPv6 address, or trying to resolve IPv6. Better remove it if it’s not required.
Remove IPv6 in Windows Vista

4) Clear DNS Cache

You can remove any DNS cache from computer, so next time DNS request will be solved by updated DNS server. This will avoid your computer to try broken or changed DNS records from cache. To clear DNS cache, open command prompt as administrator and type ipconfig /flushdns
Ceaer DNS Cache in Vista

5) Disable Wireless Network and any additional (including Virtual adapters) network adapters.

If you will not be using wireless network or it’s your secondary network, I recommend you to disable wireless network in windows 7 under network connection.  If it’s enabled, windows 7 computer will be trying to connect available wireless network around you, and trying to login though its network. Loading your profiles and start up programs will be slow while booting because of this.

6) Modifying Link Speed &amp; Duplex Value in Network adapter Properties.

This step also helps sometimes when you face problem with windows 7 network slow. I can’t say which option will work better, because it depends on your physical network setup (network adapter, cable type, LAN speed and network switch). By default it is set for Auto Negotiation. But you can play around with Value options and find out which is working better for your computer and network.

Windows 7 Network slow

I’m sure above steps will help to solve windows 7 network slow. Feel free to suggest any additional steps you did to solve windows 7 network slow, or problems you face to fix it.

1.Start Registry Editor (Regedt32.exe).
2.Locate and click the following registry key:

HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Services\InetInfo\Parameters\DispatchEntries

3.Click the value for the service that you attempted to start.
4.On the Edit menu, click Multi String, and then add the following values:

Ldapsvc
Smtpsvc
Nntpsvc
Imap4svc
Pop3svc
Resvc

2. Open the Command Prompt (run as administrator), remove Office file cache and folders by running the commands below:

1) cd %USERPROFILE%\AppData\Local\Microsoft\Office\15.0\
2) rmdir OfficeFileCache /s
3) cd %USERPROFILE%\AppData\Local\Microsoft\Office\
4) rmdir Spw /s

3. If the issue persists after doing this, sometimes Repair Office can be a good solution. Please try to Repair Office from the Control Panel and check to see whether these issues still exist.